event OLEDragOver (Data as ExDataObject, Effect as Long, Button as Integer, Shift as Integer, X as OLE_XPOS_PIXELS, Y as OLE_YPOS_PIXELS, State as Integer)
Occurs when one component is dragged over another.

TypeDescription
Data as ExDataObject An ExDataObject object containing formats that the source will provide and, in addition, possibly the data for those formats. If no data is contained in the ExDataObject, it is provided when the control calls the GetData method. The SetData and Clear methods cannot be used here
Effect as Long A Long set by the target component identifying the action that has been performed (if any), thus allowing the source to take appropriate action if the component was moved (such as the source deleting the data). The possible values are listed bellow.
Button as Integer An integer which acts as a bit field corresponding to the state of a mouse button when it is depressed. The left button is bit 0, the right button is bit 1, and the middle button is bit 2. These bits correspond to the values 1, 2, and 4, respectively. It indicates the state of the mouse buttons; some, all, or none of these three bits can be set, indicating that some, all, or none of the buttons are depressed.
Shift as Integer These bits correspond to the values 1, 2, and 4, respectively. The shift parameter indicates the state of these keys; some, all, or none of the bits can be set, indicating that some, all, or none of the keys are depressed. For example, if both the CTRL and ALT keys were depressed, the value of shift would be 6.
X as OLE_XPOS_PIXELS A single that specifies the current X location of the mouse pointer. The X value is always expressed in container coordinates
Y as OLE_YPOS_PIXELS A single that specifies the current Y location of the mouse pointer. The Y value is always expressed in container coordinates.
State as Integer An integer that corresponds to the transition state of the control being dragged in relation to a target form or control. The possible values are listed bellow.
The settings for effect are:

The settings for state are:

Note  If the state parameter is 1, indicating that the mouse pointer has left the target, then the x and y parameters will contain zeros.
The source component should always mask values from the effect parameter to ensure compatibility with future implementations of ActiveX components. As a precaution against future problems, drag sources and drop targets should mask these values appropriately before performing any comparisons.
For example, a source component should not compare an effect against, say, exOLEDropEffectCopy, such as in this manner:

If Effect = exOLEDropEffectCopy...
Instead, the source component should mask for the value or values being sought, such as this:
If Effect And exOLEDropEffectCopy = exOLEDropEffectCopy...
-or-
If (Effect And exOLEDropEffectCopy)...
This allows for the definition of new drop effects in future versions while preserving backwards compatibility with your existing code.
The control supports only manual OLE drag and drop events.

Syntax for OLEDragOver event, /NET version, on: 

// OLEDragOver event is not supported. Use the DragEnter,DragLeave,DragOver, DragDrop ... events.


// OLEDragOver event is not supported. Use the DragEnter,DragLeave,DragOver, DragDrop ... events.

Syntax for OLEDragOver event, /COM version, on: 

private void OLEDragOver(object sender, AxEXSWIMLANELib._ISwimLaneEvents_OLEDragOverEvent e)
{
}


void OnOLEDragOver(LPDISPATCH Data,long FAR* Effect,short Button,short Shift,long X,long Y,short State)
{
}


void __fastcall OLEDragOver(TObject *Sender,Exswimlanelib_tlb::IExDataObject *Data,long * Effect,short Button,short Shift,int X,int Y,short State)
{
}


procedure OLEDragOver(ASender: TObject; Data : IExDataObject;var Effect : Integer;Button : Smallint;Shift : Smallint;X : Integer;Y : Integer;State : Smallint);
begin
end;


procedure OLEDragOver(sender: System.Object; e: AxEXSWIMLANELib._ISwimLaneEvents_OLEDragOverEvent);
begin
end;


begin event OLEDragOver(oleobject Data,long Effect,integer Button,integer Shift,long X,long Y,integer State)
end event OLEDragOver


Private Sub OLEDragOver(ByVal sender As System.Object, ByVal e As AxEXSWIMLANELib._ISwimLaneEvents_OLEDragOverEvent) Handles OLEDragOver
End Sub


Private Sub OLEDragOver(ByVal Data As EXSWIMLANELibCtl.IExDataObject,Effect As Long,ByVal Button As Integer,ByVal Shift As Integer,ByVal X As Single,ByVal Y As Single,ByVal State As Integer)
End Sub


Private Sub OLEDragOver(ByVal Data As Object,Effect As Long,ByVal Button As Integer,ByVal Shift As Integer,ByVal X As Long,ByVal Y As Long,ByVal State As Integer)
End Sub


LPARAMETERS Data,Effect,Button,Shift,X,Y,State



PROCEDURE OnOLEDragOver(oSwimLane,Data,Effect,Button,Shift,X,Y,State)
RETURN

Syntax for OLEDragOver event, /COM version (others), on: 

<SCRIPT EVENT="OLEDragOver(Data,Effect,Button,Shift,X,Y,State)" LANGUAGE="JScript">
</SCRIPT>


<SCRIPT LANGUAGE="VBScript">
Function OLEDragOver(Data,Effect,Button,Shift,X,Y,State)
End Function
</SCRIPT>


Procedure OnComOLEDragOver Variant llData Integer llEffect Short llButton Short llShift OLE_XPOS_PIXELS llX OLE_YPOS_PIXELS llY Short llState
	Forward Send OnComOLEDragOver llData llEffect llButton llShift llX llY llState
End_Procedure


METHOD OCX_OLEDragOver(Data,Effect,Button,Shift,X,Y,State) CLASS MainDialog
RETURN NIL


// OLEDragOver event is not supported. Use the DragEnter,DragLeave,DragOver, DragDrop ... events.


function OLEDragOver as v (Data as OLE::Exontrol.SwimLane.1::IExDataObject,Effect as N,Button as N,Shift as N,X as OLE::Exontrol.SwimLane.1::OLE_XPOS_PIXELS,Y as OLE::Exontrol.SwimLane.1::OLE_YPOS_PIXELS,State as N)
end function


function nativeObject_OLEDragOver(Data,Effect,Button,Shift,X,Y,State)
return